What it exposes
| Feature | Property | Values | Control |
|---|---|---|---|
| Pressure (1) | pressure_1 | kPa | read only |
| Bar (1) | bar_1 | bar | read only |
| Psi (1) | psi_1 | psi | read only |
| Temperature (1) | temperature_1 | °C | read only |
| Pressure offset (1) | pressure_offset_1 | hPa · -1000…1000 | settable |
| Temperature offset (1) | temperature_offset_1 | °C · -25…25 | settable |
| Pressure (2) | pressure_2 | kPa | read only |
| Bar (2) | bar_2 | bar | read only |
| Psi (2) | psi_2 | psi | read only |
| Temperature (2) | temperature_2 | °C | read only |
| Pressure offset (2) | pressure_offset_2 | hPa · -1000…1000 | settable |
| Temperature offset (2) | temperature_offset_2 | °C · -25…25 | settable |
| Mains voltage | mains_voltage | V | read only |
| Battery | battery | % · 0…100 | read only |
| Low battery | battery_low | — | read only |
| Uptime | uptime | Hours | read only |
| Reading interval | reading_interval | sec · 5…360 | settable |
| Sensor type | sensor_type | 0-1bar, 0-5bar, 0-6bar, 0-8bar, 0-10bar, 0-12bar | settable |
| Tx radio power | tx_radio_power | 4dbm, 19dbm | settable |
| Smart sleep | smart_sleep | — | settable |
| Config report enable | config_report_enable | — | settable |
| Comparison previous data | comparison_previous_data | — | settable |
MQTT: state and commands
Zigbee2MQTT publishes the device state to zigbee2mqtt/my_device (my_device is the name you give the device). An example message:
{
"pressure_1": 1012,
"bar_1": 0,
"psi_1": 0,
"temperature_1": 21.6,
"pressure_offset_1": 0,
"temperature_offset_1": 0,
"pressure_2": 1012,
"bar_2": 0,
"psi_2": 0,
"temperature_2": 21.6,
"pressure_offset_2": 0,
"temperature_offset_2": 0,
"mains_voltage": 0,
"battery": 87,
"linkquality": 120
}
Send commands to zigbee2mqtt/my_device/set:
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"sensor_type":"0-5bar"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"tx_radio_power":"19dbm"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"smart_sleep":true}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"config_report_enable":true}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"comparison_previous_data":true}'
Watch the topics live from the browser: MQTT client.
Home Assistant automation example
Zigbee2MQTT creates Home Assistant entities from the device name. If it is called my_device, an automation in automations.yaml can look like this:
- alias: "Room too warm"
mode: single
triggers:
- trigger: numeric_state
entity_id: sensor.my_device_temperature
above: 26
for: "00:10:00"
actions:
- action: notify.notify
data:
message: "Temperature above 26 °C"
Check the YAML: YAML checker.
How to pair it
- In Zigbee2MQTT click Permit join.
- Put the device in pairing mode: usually a long press of the reset button (5–10 s) until the LED blinks; bulbs: switch the power off and on 5–6 times.
- Keep the device close to the coordinator or a router while pairing.
- Give it a clear name: MQTT topics and Home Assistant entities are built from it.
Exact procedure and model notes: the device page in the Zigbee2MQTT docs. No coordinator yet: coordinator picker.