What it exposes
| Feature | Property | Values | Control |
|---|---|---|---|
| On / off (1) | state_1 | — | settable |
| On / off (2) | state_2 | — | settable |
| On / off (3) | state_3 | — | settable |
| On / off (4) | state_4 | — | settable |
| Power (1) | power_1 | W | read only |
| Power (2) | power_2 | W | read only |
| Power (3) | power_3 | W | read only |
| Power (4) | power_4 | W | read only |
| Voltage (1) | voltage_1 | V | read only |
| Voltage (2) | voltage_2 | V | read only |
| Voltage (3) | voltage_3 | V | read only |
| Voltage (4) | voltage_4 | V | read only |
| AC frequency (1) | ac_frequency_1 | Hz | read only |
| AC frequency (2) | ac_frequency_2 | Hz | read only |
| AC frequency (3) | ac_frequency_3 | Hz | read only |
| AC frequency (4) | ac_frequency_4 | Hz | read only |
| Current (1) | current_1 | A | read only |
| Current (2) | current_2 | A | read only |
| Current (3) | current_3 | A | read only |
| Current (4) | current_4 | A | read only |
| Energy (1) | energy_1 | kWh | read only |
| Energy (2) | energy_2 | kWh | read only |
| Energy (3) | energy_3 | kWh | read only |
| Energy (4) | energy_4 | kWh | read only |
| LED Mode | led_mode | off, switch, power | settable |
| LED colors in 'switch' mode | led_colors | — | read only |
| LED brightness in 'power' mode | led_power_brightness | % · 0…100 | settable |
| LED night mode | led_night_mode | — | read only |
| Buttons enabled | buttons_enabled | — | read only |
| After power loss (1) | power_on_behavior_1 | off, on, previous, match_input | settable |
| After power loss (2) | power_on_behavior_2 | off, on, previous, match_input | settable |
| After power loss (3) | power_on_behavior_3 | off, on, previous, match_input | settable |
| After power loss (4) | power_on_behavior_4 | off, on, previous, match_input | settable |
| Wi-Fi status | wifi_status | — | read only |
| IP address | ip_address | — | read only |
| DHCP enabled | dhcp_enabled | — | read only |
| Wi-Fi Configuration | wifi_config | — | read only |
| Identify | identify | identify | settable |
MQTT: state and commands
Zigbee2MQTT publishes the device state to zigbee2mqtt/my_device (my_device is the name you give the device). An example message:
{
"state_1": "ON",
"state_2": "ON",
"state_3": "ON",
"state_4": "ON",
"power_1": 12.4,
"power_2": 12.4,
"power_3": 12.4,
"power_4": 12.4,
"voltage_1": 230,
"voltage_2": 230,
"voltage_3": 230,
"voltage_4": 230,
"ac_frequency_1": 0,
"ac_frequency_2": 0,
"linkquality": 120
}
Send commands to zigbee2mqtt/my_device/set:
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"state_1":"TOGGLE"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"state_2":"TOGGLE"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"state_3":"TOGGLE"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"state_4":"TOGGLE"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"led_mode":"switch"}'
Watch the topics live from the browser: MQTT client.
Home Assistant automation example
Zigbee2MQTT creates Home Assistant entities from the device name. If it is called my_device, an automation in automations.yaml can look like this:
- alias: "Turn off when idle"
mode: single
triggers:
- trigger: numeric_state
entity_id: sensor.my_device_power
below: 2
for: "00:15:00"
actions:
- action: switch.turn_off
target:
entity_id: switch.my_device_1
Check the YAML: YAML checker.
How to pair it
- In Zigbee2MQTT click Permit join.
- Put the device in pairing mode: usually a long press of the reset button (5–10 s) until the LED blinks; bulbs: switch the power off and on 5–6 times.
- Keep the device close to the coordinator or a router while pairing.
- Give it a clear name: MQTT topics and Home Assistant entities are built from it.
Exact procedure and model notes: the device page in the Zigbee2MQTT docs. No coordinator yet: coordinator picker.