What it exposes
| Feature | Property | Values | Control |
|---|---|---|---|
| Energy | energy | kWh | read only |
| Voltage | voltage | V | read only |
| Current | current | A | read only |
| Power | power | W | read only |
| AC frequency | ac_frequency | Hz | read only |
| Power factor | power_factor | % | read only |
| Temperature | temperature | °C | read only |
| Event | event | normal, over_current_trip, over_power_trip, high_temp_trip, over_voltage_trip, under_voltage_trip, over_current_alarm, over_power_alarm … | read only |
| Over current setting | over_current_setting | Ignore, Alarm | settable |
| Over current threshold | over_current_threshold | A · 1…50 | settable |
| Over voltage setting | over_voltage_setting | Ignore, Alarm | settable |
| Over voltage threshold | over_voltage_threshold | V · 240…295 | settable |
| Under voltage setting | under_voltage_setting | Ignore, Alarm | settable |
| Under voltage threshold | under_voltage_threshold | V · 90…220 | settable |
| Temperature setting | temperature_setting | Ignore, Alarm | settable |
| Temperature threshold | temperature_threshold | °C · -25…80 | settable |
| Over power setting | over_power_setting | Ignore, Alarm | settable |
| Over power threshold | over_power_threshold | W · 1000…26000 | settable |
MQTT: state and commands
Zigbee2MQTT publishes the device state to zigbee2mqtt/my_device (my_device is the name you give the device). An example message:
{
"energy": 3.21,
"voltage": 230,
"current": 0.06,
"power": 12.4,
"ac_frequency": 0,
"power_factor": 0,
"temperature": 21.6,
"event": "normal",
"over_current_setting": "Ignore",
"over_current_threshold": 26,
"over_voltage_setting": "Ignore",
"over_voltage_threshold": 268,
"under_voltage_setting": "Ignore",
"under_voltage_threshold": 155,
"linkquality": 120
}
Send commands to zigbee2mqtt/my_device/set:
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"over_current_setting":"Alarm"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"over_voltage_setting":"Alarm"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"under_voltage_setting":"Alarm"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"temperature_setting":"Alarm"}'
mosquitto_pub -t zigbee2mqtt/my_device/set -m '{"over_power_setting":"Alarm"}'
Watch the topics live from the browser: MQTT client.
Home Assistant automation example
Zigbee2MQTT creates Home Assistant entities from the device name. If it is called my_device, an automation in automations.yaml can look like this:
- alias: "Room too warm"
mode: single
triggers:
- trigger: numeric_state
entity_id: sensor.my_device_temperature
above: 26
for: "00:10:00"
actions:
- action: notify.notify
data:
message: "Temperature above 26 °C"
Check the YAML: YAML checker.
How to pair it
- In Zigbee2MQTT click Permit join.
- Put the device in pairing mode: usually a long press of the reset button (5–10 s) until the LED blinks; bulbs: switch the power off and on 5–6 times.
- Keep the device close to the coordinator or a router while pairing.
- Give it a clear name: MQTT topics and Home Assistant entities are built from it.
Exact procedure and model notes: the device page in the Zigbee2MQTT docs. No coordinator yet: coordinator picker.