DETA Outdoor Double Powerpoint (6294HA Series 2): ESPHome

Starter ESPHome config

Built from the pinout above. Keys and the Wi-Fi password come from secrets.yaml in ESPHome. Check the pins against your hardware revision before flashing: one model can ship with different boards.

substitutions:
  name: deta-outdoor-double-powe

esphome:
  name: ${name}
  friendly_name: "DETA Outdoor Double Powerpoint (6294HA Series 2)"

bk72xx:
  board: generic-bk7231n-qfn32-tuya  # BK7231T or BK7231N: check the chip marking

logger:
api:
  encryption:
    key: !secret api_key
ota:
  - platform: esphome
    password: !secret ota_password
wifi:
  ssid: !secret wifi_ssid
  password: !secret wifi_password
  ap: {}
captive_portal:

switch:
  - platform: gpio
    pin: GPIO13
    id: relay1
    name: "Relay 1"  # Relay 1
    restore_mode: RESTORE_DEFAULT_OFF
  - platform: gpio
    pin: GPIO14
    id: relay2
    name: "Relay 2"  # Relay 2
    restore_mode: RESTORE_DEFAULT_OFF
  - platform: gpio
    pin: P8
    id: relay3
    name: "Relay 3"  # Relay 1
    restore_mode: RESTORE_DEFAULT_OFF
  - platform: gpio
    pin: P26
    id: relay4
    name: "Relay 4"  # Relay 2
    restore_mode: RESTORE_DEFAULT_OFF

binary_sensor:
  - platform: gpio
    pin:
      number: GPIO4
      mode: INPUT_PULLUP
      inverted: true
    name: "Button 1"  # Button 1 (inverted)
    on_press:
      - switch.toggle: relay1
  - platform: gpio
    pin:
      number: GPIO12
      mode: INPUT_PULLUP
      inverted: true
    name: "Button 2"  # Button 2 (inverted)
    on_press:
      - switch.toggle: relay2
  - platform: gpio
    pin:
      number: P7
      mode: INPUT_PULLUP
      inverted: true
    name: "Button 3"  # Button 1 (inverted)
    on_press:
      - switch.toggle: relay3
  - platform: gpio
    pin:
      number: P24
      mode: INPUT_PULLUP
      inverted: true
    name: "Button 4"  # Button 2 (inverted)
    on_press:
      - switch.toggle: relay4

status_led:
  pin:
    number: GPIO5
    inverted: true  # LED (inverted)

# Other pins from the pinout:
#   P6: LED (inverted)
#   GPIO3: RX for CSE7766
#   RX1: RX for CSE7766

How to flash

• Most devices are flashed over UART: a 3.3 V USB-TTL adapter to RX, TX, GND and 3V3, holding GPIO0 to ground at power-on (ESP8266/ESP32). Mains power disconnected.
• Beken (BK72xx) and Realtek chips are flashed with ltchiptool, or with cloudcutter without opening the case if the firmware allows it.
• Details and board photos: the device page in the ESPHome database.

A config from scratch: ESPHome generator. Which pins are safe: pinout.

Similar devices

• Deta Grid Connect Double Powerpoint with Dual USB 6920HA
• Deta Grid Connect Smart Double Touch Power Point
• DETA Grid Connect Smart Inline Switch 6000HA
• DETA Grid Connect Smart Plug Base
• DETA Outdoor Double Powerpoint (6294HA)
• Digitaling 20A Power Monitor RTL8710BX t102-v1.1
• EKF Сonnect PRO Wi-Fi (RCS-2-WF) Smart Plug
• Emporia Smart Plug